Видео

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

I would have to clean all of that dirt up before I opened the tank.

Great video. Details of it being a v6 or v8 should have been shared.

I have a 97 Nissan Pathfinder where is the speed sensor located ?

Appreciate the TJ love.

I just spent a month derusting everything she touched on that TJ.

My Mg Service changed that for my MG5 free as a part of warranty issue.

A well-done video. Thank you!

Very helpful video!! Thank you for posting 👍👍

thank you!!

i take it this a joke

If I put it on a lift, is it possible to work on it without removing the fan?

Do you have to take oil filter off to get to it?

Very informative video

Nicely done video. Very informative. Thanks.

What size screws did you use to put the plastic pieces back together? The ones where you had to drill out the plastic rivets.

Extraordinary detail ! Super helpful !! I learned lots !!! Thanks mate . 👊🏼 🔥

When are you going to start shipping to Canada?

La. Berda muy bien esplicado te felicito muy buen tenico

My 2013 transit connect air conditioning works only on fan speed 1. raising fan speed to 2, 3, and 4 shuts off air conditioning. could this be the blower motor resistor?

Respect.

I had this done recently and I'm trying to figure out how I can tell if they actually did the job, what's the easiest way to tell?

Can you upload a video of water pump replacement of 2010 lexus Rx 350. Please

I thought the oil would be dark. Due to all the rust.😮

Awesome video! Even more so that you give the socket sizes and torque specs. The mounting bracket nuts both spun, but you even warned of that so I was ready for it. Had to apply some heat to one of the bottom bolts, but the other 5 all pulled right out.

Yeah, How did you cut those bolts?

76 ft/lbs for lug nuts? Is that because they are aftermarket?

Hello everyone I have a 2017 impala premier 3.6L flex fuel. I'm having difficulties taking the rear motor mount from the vehicle..the mount is in between the frame and the engine. Any suggestions?? Please let me know..

Excellent video , good work

Could you show this in a 2020 Escape?

What a joke. Take the bed off. Whats with the jacking it up and taking straps off. Nobody does that on a Ranger.

Damn good in-depth instructions for a project I'm about to start. I only had PLPD and can't afford to pay and have it fixed. Thanks, I'll check you parts page out after watching this.

That's what I need to be watching. My 17 year old just demolished the front end on my 2007 TL-S. Radiator and most intact but wheel wellls, fog plastic, bumper, grill and ... I had this new for 17 years and saved it for him. It took him less than 17 days to hot dog it. 😞

Worked great. Thanks for the video

Did you replace the race that you took off the hub ? It doesn't show that step.

You can totally get that busted sensor out without removing the knuckle. I better post a how to, lol.

How do you fix the j nut if it’s stripped out already..?

Thanks!

Looks very easy.

Thank you for this video

After a radiator replaced there is still leaking oil and my splash shield has tears and needs replacing too!

3:10 Hi, what was the socket size used for these two Phillips screws? I am struggling to remove since they are rusted in. Drenched them in pb for a couple days and nothing.

When you are master of your craft everything looks easy. I, on the other hand would be scrapping knuckles just to dislodge battery tray.

How do you replace just the tail light cover?

Clutch timing on this video. Thanks. !!

Was considering replacing the headlights on my 2014 explorer . Welp not anymore. You seriously half to disassemble the front end of the vehicle just to swap out the headlamps??? What were they thinking!!???

How exactly do you allign the actuator with the door?

How you programmed key though ?

The bolt on mine was also seized like that. I had to buy something to cut it and a replacement bolt, but it was still cheaper than taking it to a mechanic and it was a great learning experience.

So... say I tried this and one of the bolts coming from the engine is one that snapped. What do? Lol